Print

Harry Potter Necklace

Represent your Hogwarts house with these DIY fizzy pop necklaces.
Keyword: Crafting, Harry Potter, Jewelry, Tutorial

Materials

Instructions

  • First you will need to cut your wire the desired length of your necklace plus 1.5 inches on each side. My wire is 16 inches long, plus the 1.5 inches on each side, for a total of 19 inches.
  • Close a 6mm jump ring and slide it on the end of your wire. Loop the wire around the ring and then slide two crimp beads over both sections of wire. Use a pair of pliers to crimp the crimp beads down until they are tight and flat. You can also add an extender chain at this point, if you want to. For detailed instructions on adding an extender chain, check out the Fizzy Pops tutorial here.
  • After your beads are crimped. you are ready to add your necklace beads. Here are the necklace patterns.

The Gryffindor Necklace:

  • Burgundy
  • Gold Star Dust Bead
  • Gold Faux Pearl
  • Gold Star Dust Bead
  • (repeated 5x)
  • bottle cap pendant
  • Burgundy
  • Gold Star Dust Bead
  • Gold Faux Pearl
  • Gold Star Dust Bead
  • (repeated 5x)

The Hufflepuff Necklace:

  • Yellow Bead
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • Yellow Striped Bead
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • Yellow Bead
  • Gold Star Dust Bead
  • Black  Bead
  • Gold Star Dust Bead
  • Yellow Striped Bead
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • bottle cap pendant
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • Yellow Striped Bead
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • Yellow Bead
  • Gold Star Dust Bead
  • Black  Bead
  • Gold Star Dust Bead
  • Yellow Striped Bead
  • Gold Star Dust Bead
  • Black Bead
  • Gold Star Dust Bead
  • Yellow Bead

The Ravenclaw Necklace:

  • Brown Faux Peal Bead
  • Blue Striped Bead
  • Blue Faux Peak Bead
  • Silver Star Dust Bead
  • (repeated 4x)
  • bottle cap pendant
  • Brown Faux Peal Bead
  • Blue Striped Bead
  • Blue Faux Peak Bead
  • Silver Star Dust Bead
  • (repeated 4x)

The Slytherin Necklace:

  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Ice Cube Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Green Faceted Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Ice Cube Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Green Faceted Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Ice Cube Bead
  • Silver Star Dust Bead
  • bottle cap pendant
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Green Faceted Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Ice Cube Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Green Faceted Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Ice Cube Bead
  • Silver Star Dust Bead
  • Green Striped Bead
  • Silver Star Dust Bead
  • Green Faceted Bead
  • Slide a lobster clasp onto a 6mm jump ring and then close the jump ring. Slide the jump ring onto the wire and then double back the wire through the crimp beads and a couple extra of the necklace beads. Crimp the crimp beads until they are tight and then trim the excess wire.
  • You necklace is now ready to add the image to the center! I did a google search for each of the house crests. I cropped each crest to be about 3/4 of an inch high. Use a 1 inch circle hole punch to punch out the image after it is printed.
  • Place an epoxy sticker on top of the image and rubbed the back to make sure all air bubbles were gone. Add a small amount of a strong glue (like E-6000) to the bottle cap and gently press your image with epoxy sticker to the bottle cap.
  • Allow the glue to dry completely before wearing.